7

I have been having significant issues with the usability/reliability of my wireless cards. I have tried several fixes over the past few days. I am running ubuntu 14.04 LTS. I go from 1/10 of the speed i should be getting to not working at all. It does drop sometimes as well. (The above is in regards to my PCI RTL8192ce card)

I recently tried to install a usb wifi adapter (RTL8192cu) and I cannot even get that one to connect well enough to use. ( basically shows no "bars" on the wireless icon on the top right)

I have tried to install the realtek drivers from the realtek site but I had a couple errors with the install. (I have the output somewhere if it is needed.) I have tried as well to use the fix found here: https://sites.google.com/site/easylinuxtipsproject/reserve-7 to no avail. I would appreciate your assistance in fixing this. (There may be a question already solving this but I have tried 2-4 fixes over the past 2 days and none worked)

Iamalinuxnoob
  • 71
  • 1
  • 1
  • 2
  • The Q&A mentions the exact card model for 14.04 thus this is probably a duplicate: http://askubuntu.com/questions/414974/realtek-rtl8192ce-wireless-slow-intermittent-access?rq=1 – fossfreedom May 23 '14 at 18:59
  • That was actually the one I tried right before making this post. It didn't work unfortunately. – Iamalinuxnoob May 23 '14 at 19:16
  • Please do what is in the accepted answer in the link below so we may see the information needed to help diagnose the issue. – Wild Man May 24 '14 at 01:26
  • @fossfreedom In regards to the PCI card that link may help but the USB card will not work without installing one of the available versions from github. – mchid Mar 02 '16 at 21:47

3 Answers3

7

It's a driver issue.

You might want to check out this thread. http://ubuntuforums.org/showthread.php?t=2148130&page=2

https://github.com/pvaret/rtl8192cu-fixes

COPIED FROM GITHUB:

Ensure you have the necessary prerequisites installed:

sudo apt-get install linux-headers-generic build-essential dkms git

Clone this repository:

git clone https://github.com/pvaret/rtl8192cu-fixes.git

Set it up as a DKMS module:

sudo dkms add ./rtl8192cu-fixes

Build and install it:

sudo dkms install 8192cu/1.10

Refresh the module list:

sudo depmod -a

Ensure the native (and broken) kernel driver is blacklisted:

sudo cp ./rtl8192cu-fixes/blacklist-native-rtl8192.conf /etc/modprobe.d/

And reboot. You're done.

Kyle Heuton
  • 103
  • 2
Anon
  • 96
  • 1
  • 3
1

I have had the same issues, until I installed the DKMS driver via https://github.com/vincent-t/rt8192cu_dkms

My 8192cu is fast and stable since that driver was installed.

Sjaak Trekhaak
  • 161
  • 1
  • 3
  • The installation procedure for this solution is much more automated than the other solution suggested on this page. One command `sudo make install_dkms` is all what is required for installation. – Serge Stroobandt Sep 22 '15 at 11:44
0

I also had a problem with connecting rtl8192ce (EdiMax EW-7612PIn V2) from my ubuntu 14.04. Actually the issue was only with APs not supporting N draft (so the old b/g standard). I checked three different boxes and all had the same issue. I had however no issues with the one AP that had N-draft support. The problem was that the default bitrate with old APs was always set to 1Mb/s even though the link quality was 70/70. But I was not even able to ping default gw. So the solution was to issue:

/sbin/iwconfig wlan0 rate auto

Unfortunately I do not see an option in ubuntu NetworkManager to specify bitrate (I do not use configuration from /etc/network/interfaces) so I added the iwconfig command to

/etc/init.d/wifirifi

and issued

chmod ugo+rx
update-rc.d wifirifi defaults
fakej
  • 1
  • 1